No standard gives one storage life for a whole seal. The rubber parts and the flatness of the faces age separately, and each seal maker sets its own limits for its own seals.

How long a seal lasts once it is running in the pump is a separate question, covered in how long mechanical seals last.

What Limits the Shelf Life of a Stored Mechanical Seal

Two parts of a stored seal age: the elastomers and the lapped faces.

Elastomers

O-rings, gaskets and rubber bellows harden, soften, crack or craze on the shelf, driven by heat, light, ozone, oxygen and humidity.

An assembled seal adds a second effect. An O-ring held compressed in its groove takes a compression set over time and pushes back with less sealing force once the seal is installed.

Seal Faces

Seal faces are lapped flat and their flatness is measured in light bands, so a change in shape far too small to see is enough to open a leak path. Over a long storage period, the storage environment can change that flatness.

Shelf Life by Elastomer

The per-elastomer figures that circulate freely come from a cancelled standard or a withdrawn edition, so none of them is a current limit. The standard behind the widely repeated “15 years” and “unlimited” figures, SAE ARP5316, was cancelled in October 2018. ISO 2230, the rubber storage standard, was replaced in 2026 by a third edition; its storage periods are in the purchased standard, and a period quoted for a compound from the 2002 edition may no longer apply.

The old ARP5316 table still shows which secondary seal materials age fastest. For mechanical seal secondary seals, the table as it stood in 2007 reads:

MaterialMaximum shelf life, SAE ARP5316 (cancelled 2018)
Chloroprene (CR)15 years
Nitrile (NBR)15 years
Ethylene propylene rubber (EPR)15 years
Fluoroelastomer (FKM)Unlimited
Perfluoroelastomer (FFKM)Unlimited
Silicone (Q)Unlimited
PTFEUnlimited
Glass-filled PTFEUnlimited
Graphite-filled PTFEUnlimited
Flexible graphiteUnlimited

These ARP5316 values are maximums for unused, as-received parts kept at no more than 38 °C, away from contamination, sunlight and ozone.

Plan by the elastomer shelf life in the instructions for your seal instead.

When the Shelf-Life Clock Starts

ISO 2230 counts a rubber part’s storage period from the time of manufacture, so the elastomers in a spare seal start ageing when they are moulded, before the seal is assembled, shipped or received.

If the box carries no date, ask the supplier for the build date at delivery, and treat the delivery date as the latest the clock can have started. Write that date on the box and issue the oldest seals first.

How to Store Spare Mechanical Seals

Keep spare seals in their original packaging, in a dry, dust-free, ventilated room at room temperature, away from direct sunlight, heat sources, ozone-producing electrical equipment and vibration. If a seal is unpacked for inspection, repack it in its original packaging.

Where the instructions for your seal give a storage temperature or humidity range, keep the store inside it. A seal that has been stored colder or hotter than room temperature should be unboxed in a clean room at room temperature and left to recover before installation.

When to Store a Seal Disassembled

No standard sets a point for taking a boxed spare apart.

Check the seal maker’s instructions before taking a cartridge apart.

For a seal left installed in an idle pump, turn the shaft one to two revolutions by hand every three months, and once the pump has stood more than 24 months, remove the seal, disassemble, clean and dry it, and store it as individual components.

Using a Seal Past Its Shelf Life

A seal past its storage period can usually still be installed once its elastomers are cleared or replaced and its faces are confirmed flat or re-lapped.

Check every O-ring and gasket for cracks, swelling, hardness change and compression set, and replace them when in doubt. Test the faces on an optical flat under a helium light: the acceptance is normally within two light bands, and a face outside it is re-lapped. Then static or air test the assembled seal before it goes into service.

Before re-kitting or re-lapping a long-stored seal, check the instructions for your seal.