Crystallization makes a mechanical seal leak because the solids jam the parts that keep the faces closed and open leak paths between and across the faces. You stop it by keeping the fluid from turning solid on whichever side of the faces it crystallizes, and by using a seal that keeps working when some crystals form anyway. On chemical pump seals handling caustic or salt solutions, the usual fixes are a quench outboard, a clean flush or barrier fluid at the faces, and temperature control for the seal chamber.

Where Crystals Form at a Pump Seal

Crystals form in two places: on the atmospheric side, where the seal’s normal leakage dries out, and on the product side, where the liquid at the faces or in the seal chamber passes its solubility limit.

On the atmospheric side, the seal’s normal leakage evaporates and the dissolved solids stay, building a crust on the sleeve and around the shaft-side secondary seal, outboard of the faces.

On the product side, two things push the liquid past saturation. Heat at the faces drives water out of the fluid film until the caustic concentrates beyond its solubility limit and solids form on the sealing surfaces. And liquid left standing in the seal chamber can cool below its crystallization temperature while the pump is idle.

Any solution running close to saturation at the seal should behave the same way.

How Crystals Make the Seal Leak

Crystals open a leak path in three ways: hang-up, face separation and abrasive wear.

Crystals Lock the Springs or Bellows

A seal keeps its faces closed only while the spring-loaded face can move axially, following shaft movement, thermal growth and face wear. Crystals packed into spring coils, drive slots or bellows convolutions freeze that face in place, so the next time the shaft shifts, the faces separate and the seal leaks.

On a metal bellows, deposits on the plates also stop them flexing evenly, which distorts the seal. The same deposit around a dynamic O-ring stops it sliding.

Crystals Hold the Faces Open

Crystals that form in the fluid film, or that were left on the faces at standstill, sit between the faces as solid particles much thicker than the film itself. They prop the faces apart, and the gap they hold open lets product straight through.

Crystals Score the Faces and Sleeve

Crystals are hard and abrasive, so the ones carried across the interface wear the faces as they turn. The grooved faces no longer close flat, and the softer face of the pair, often carbon, takes most of the damage.

The sleeve suffers the same way under a dynamic O-ring that crystals have packed around: the trapped particles cut into the sleeve as the O-ring moves, until fluid can pass under it.

When a Crystallization Leak Shows Up

A crystallization leak most often appears at startup after the pump has stood idle, because that is when the chamber fluid has had time to cool and crystallize and the outboard crust has had time to set hard.

During running, the leak tends to arrive in two other ways. Outboard deposits build slowly until a thermal or pressure change requires the face to move and it cannot, so the seal goes from dry to leaking at once. Inboard, leakage rises gradually as abrasive crystals wear the faces.

How to Tell Crystallization From Other Seal Failures

A removed seal failed from crystallization when solid deposits sit in the places that move: spring coils packed, bellows convolutions filled, crust around the dynamic O-ring and on the sleeve outboard of the faces. A white or salt-colored crust on the atmospheric side of the gland is the outside sign of the same thing.

The faces and sleeve then confirm it. Look for:

  • Hang-up: the spring-loaded face stuck in one axial position, with the O-ring that should slide held fast by deposits.
  • Abrasive wear: concentric grooves across the face, deepest on the softer face, rather than the heat checking or blistering of a dry-running seal.
  • Sleeve scoring: a cut band in the sleeve exactly under the dynamic O-ring, where trapped crystals worked as the O-ring moved.

A seal with clean springs and a smooth sleeve but heat-cracked or chemically etched faces failed some other way, and reading the face damage is the next step.

How to Stop Crystals From Forming at the Seal

Match the fix to where the crystals are: a quench for outboard deposits from dried leakage, a clean flush or pressurized barrier for crystals at the faces, and temperature and shutdown control for crystals that form in the chamber while the pump stands. Seal design covers whatever crystals still form, by keeping the seal working around them.

Harder faces, such as sintered silicon carbide on both faces, and more resistant elastomers do not stop crystals forming; they only change how the seal wears when crystals are present.

Atmospheric-Side Quench

A quench stops crystals forming outboard when the deposit comes from leakage drying out: a quench medium on the atmospheric side of the faces washes the residue away before it builds, and drains it off. Water suits deposits that dissolve in water, such as caustic; steam is used where the solids are hydrocarbons.

Product-Side Flush or Barrier Fluid

A clean flush or a pressurized barrier keeps crystals off the product side when it replaces the product at the seal with a clean liquid. An API Plan 32 flush injects clean liquid from an outside source at slightly above seal chamber pressure, so caustic stays out of the chamber. The flow needed to hold the caustic back is high, and its cost can rule Plan 32 out.

A dual unpressurized seal does not solve the problem by itself: inner seal leakage carries the caustic into the buffer fluid, which then becomes the crystallizing liquid. It needs a Plan 32 on the inner seal as well.

A dual pressurized seal, with barrier fluid above process pressure, lets the faces run on clean barrier fluid and keeps process solids out of the face area. The inboard seal’s process-side parts still sit in the product. It costs the most to install and generally runs the most reliably of the three.

Temperature Control and Shutdown Practice

Temperature control keeps the fluid at the seal inside the range where it stays in solution: not so hot at the faces that water boils off and concentrates it, and not so cold in the chamber that it drops below its crystallization temperature. Seal chamber cooling addresses the first; heat tracing or a heating jacket on the chamber addresses the second.

Before a long stop, flush the seal chamber with clean liquid or keep the chamber heated through the standby. This matters most on pumps that stand idle for long periods and on solutions running close to their solubility limit.

Seal Designs That Resist Hang-Up

A rotating metal bellows keeps working best where caustic can come out of solution: spinning the bellows helps keep the convolutions clear of debris, and with no dynamic O-ring there is nothing to hang up on the sleeve. Specify metal bellows seals for crystallizing duty as rotating rather than stationary.

Where a pusher seal is used, a single large coil spring resists clogging better than a set of small springs, at the cost of less even face loading. API 682’s Type A seal, a multi-spring pusher with a dynamic O-ring, depends on the quench or flush above to keep its springs and O-ring clean on crystallizing duty.